Juniper Networks EX-SFP-10GE-DAC-1MA Compatible 10G SFP+ Active Copper Twinax Cable, 1m (3ft)

This HT cable matches the EX-SFP-10GE-DAC-1MA requirement for Juniper Networks equipment. The 1m (3ft) assembly supports 10G operation and provides a factory-terminated passive copper link without separate optical modules or patch cords; its complete electrical and mechanical details are listed below.

OEM Part Number: EX-SFP-10GE-DAC-1MAHT Part Number: EX-SFP-10GE-DAC-1MA

Product Highlights

• Compatible alternative to Juniper Networks EX-SFP-10GE-DAC-1MA
• 10G connectivity at 10Gbps
• Interface configuration: SFP+ to SFP+
• Fixed length and part number: 1m (3ft), EX-SFP-10GE-DAC-1MA
• Cable construction: Active Twinax
• Conductor specification: 30AWG
• Maximum power consumption: ≤0.5W
• Minimum bend radius: 23mm

Juniper platform documentation distinguishes straight QSFP28 DAC or AOC connections from DACBO and AOCBO breakout operation. On channelized systems, the host port must be configured for the required breakout mode. Match this HT compatible cable to the exact Juniper part number and the intended platform configuration.

EX-SFP-10GE-DAC-1MA is the shortest of 5 verified length options in this family. It is the preferred choice when the port positions are close and cable slack must be kept to a minimum. The next option is EX-SFP-10GE-DAC-3MA at 3m (10ft), adding 2m for a less direct routing path; selecting it unnecessarily would leave more cable to dress.

The rated power consumption is ≤0.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 30AWG conductors, PVC (OFNR) jacket, minimum bend radius 23mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include 1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

At 1m (3ft), EX-SFP-10GE-DAC-1MA is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.

Our compatibility setup for Juniper Networks EX-SFP-10GE-DAC-1MA is checked together with the physical 1m (3ft) assembly. Factory verification covers connector condition, host identification, error-free link establishment and electrical continuity, link stability and diagnostic readouts. Providing the exact host model and firmware release helps us identify platform-specific requirements before production.

Use part number EX-SFP-10GE-DAC-1MA for the 1m (3ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.