NVIDIA/Mellanox MCP7H60-C01 Compatible 200G QSFP-DD 8 x 25G NRZ to 2 x 100G QSFP28 4 x 25G NRZ Ethernet Passive Copper Breakout Cable, 1m (3ft)

Use the MCP7H60-C01 compatible assembly where a 200G connection is required between compatible ports. This page covers the 1m (3ft) version only, with its own HT part number, specifications and compatibility verification.

OEM Part Number: MCP7H60-C01HT Part Number: MCP7H60-C01

Product Highlights

• Compatible alternative to NVIDIA/Mellanox MCP7H60-C01
• 200G connectivity at 200Gbps
• Interface configuration: QSFP-DD to 2x QSFP28
• Fixed length and part number: 1m (3ft), MCP7H60-C01
• Cable construction: Passive Breakout DAC
• Conductor specification: 30AWG
• Maximum power consumption: 0.1W (QSFP-DD End)0.1W (QSFP28 Per End)
• Minimum bend radius: 35mm

The listed modulation format is QSFP-DD-8x 25G-NRZQSFP28-4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

At 1m (3ft), MCP7H60-C01 is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.

MCP7H60-C01 occupies the middle of this family between MCP7H60-C005 at 0.5m (2ft) and MCP7H60-C02 at 2m (7ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 0.1W (QSFP-DD End)0.1W (QSFP28 Per End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 30AWG conductors, PVC jacket, minimum bend radius 35mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD MSA, SFF-8661, IEEE 802.3bs-200GAUI-8, IEEE802.3bm-CAUI-4, CMIS 4.0, SFF-8636. Confirm that the host firmware and port configuration support the same operating mode.

The QSFP-DD to 2x QSFP28 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

The HT cable carries the compatibility configuration associated with MCP7H60-C01, while its mechanical assembly remains the fixed 1m (3ft) version described here. Incoming inspection, connector examination and a live link test are completed before packing. Customers with unusually old or new NVIDIA/Mellanox software can request a pre-order check.

Use part number MCP7H60-C01 for the 1m (3ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Every MCP7H60-C01 compatible assembly undergoes link testing, compatibility verification and visual inspection. The 1m (3ft) cable is coiled without exceeding its minimum bend radius, fitted with connector protection and packed in an anti-static bag or protective tray before cartoning. Project labels and packing lists are available for volume orders.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.