
This HT cable matches the MFS1S00-V015E requirement for NVIDIA/Mellanox equipment. The 15m (49ft) assembly supports 200G operation and provides a factory-terminated active optical link with the optical engines and fiber integrated into the assembly; its complete electrical and mechanical details are listed below.
OEM Part Number: MFS1S00-V015EHT Part Number: MFS1S00-V015E
| HT Part Number | MFS1S00-V015E |
|---|---|
| NVIDIA/Mellanox Ethernet Compatible | MFS1S00-V015E |
| Manufacturer | HT |
| Form Factor | QSFP56 to QSFP56 |
| Max. Data Rate | 200Gbps |
| Cable Length | 1m (3ft) |
| Cable Type | AOC |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VSCEL |
| Receiver Type | PIN |
| Max. Power Consumption | 4.35W Per End |
| Modulation Format | 4x 50G-PAM4 |
| CDR (Clock and Data Recovery) | TX & RX Built-in CDR |
| Jacket Material | LSZH |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | IEEE 802.3, QSFP56 MSA, SFF-8665, SFF-8636 |
| MTBF | ≈3.2 Million Hours |
The listed modulation format is 4x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
The rated power consumption is 4.35W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
This assembly uses LSZH jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include IEEE 802.3, QSFP56 MSA, SFF-8665, SFF-8636. Confirm that the host firmware and port configuration support the same operating mode.
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
The extended 15m (49ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.
MFS1S00-V015E occupies the middle of this family between MFS1S00-V010E at 10m (33ft) and MFS1S00-V020E at 20m (66ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
The HT cable carries the compatibility configuration associated with MFS1S00-V015E, while its mechanical assembly remains the fixed 15m (49ft) version described here. Incoming inspection, connector examination and a live link test are completed before packing. Customers with unusually old or new NVIDIA/Mellanox software can request a pre-order check.
Quote HT part number MFS1S00-V015E with the required quantity. The 15m (49ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.
No. It is an HT-manufactured compatible alternative for equipment that specifies NVIDIA/Mellanox MFS1S00-V015E.
No. This page is dedicated to 15m (49ft) and part number MFS1S00-V015E. Other lengths have their own part numbers and product pages.
No. The connectors and cable form one complete direct-attach assembly. Do not attempt to detach or replace either end.
No. Follow the specified minimum bend radius and route the 15m (49ft) assembly without tight folds, sharp edges or excessive cable ties.
Every MFS1S00-V015E compatible assembly undergoes link testing, compatibility verification and visual inspection. The 15m (49ft) cable is coiled without exceeding its minimum bend radius, fitted with connector protection and packed in an anti-static bag or protective tray before cartoning. Project labels and packing lists are available for volume orders.
Stock items are generally dispatched within one to three working days after order confirmation. DHL, UPS, FedEx, TNT and EMS are available for international delivery; larger consolidated orders can move by air or sea freight. Customer courier accounts and nominated forwarders are accepted.
Please write to sales@huihongfiber.com, we will reply as soon as possible.
| Fiber Optic Test Equipment |
| Fiber Optic Tool Kits |
Huihong TechnologiesAdd:6F,1st Bldg,ZYT industrial park, Shiyan area,Shenzhen,ChinaEmail:info@huihongfiber.com Tel: 86.755.61230063 Specialized fiber optic products manufacturer. |
Fiber Optic Quick Guide |
News and ExhibitionsCompany news and exhibitions schedules for this year and next year. click here for details . |
Fiber Optic Applications
|
Customer Support
|