OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT 1.6T OSFP224 8 x 200G PAM4 IHS Finned Top Passive Copper Twinax Cable, 1m (3ft)

The OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT cable offers a direct OSFP (IHS Finned Top) to OSFP (IHS Finned Top) connection at 1600Gbps. Its 1m (3ft) length and DAC construction are intended for multi-vendor equipment, with no separate transceiver-and-patch-cord assembly required.

OEM Part Number: OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FTHT Part Number: OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT

Product Highlights

• HT-manufactured DAC assembly in 1m (3ft)
• 1.6T connectivity at 1600Gbps
• Interface configuration: OSFP (IHS Finned Top) to OSFP (IHS Finned Top)
• Fixed length and part number: 1m (3ft), OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT
• Cable construction: Passive DAC
• Conductor specification: 26AWG
• Maximum power consumption: 0.1W Per End
• Minimum bend radius: 55mm

The listed modulation format is 8x 200G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

At 1m (3ft), OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.

OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT is the longest of 2 verified length options in this family. Compared with OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-0.5M2FT at 0.5m (2ft), it provides 0.5m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.

The rated power consumption is 0.1W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 26AWG conductors, PET jacket, minimum bend radius 55mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is 1.6T Ethernet. Listed interface and protocol references include OSFP MSA, IEEE 802.3. Confirm that the host firmware and port configuration support the same operating mode.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

For this Generic application, testing combines digital identification with actual traffic-link verification and electrical continuity, link stability and diagnostic readouts. Both ends are inspected for latch, boot and connector damage. If the project uses a specific hardware revision or a channelized port, send those details so that the intended configuration can be reviewed before shipment.

Use part number OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT for the 1m (3ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

HT inspects and tests every completed cable before it enters finished stock. Protective caps or covers are fitted where applicable, followed by anti-static or tray packaging and an outer carton. Custom labels can cross-reference the customer part number, OSFP (IHS Finned Top) to OSFP (IHS Finned Top)-1.6T-DAC-1M3FT and the 1m (3ft) length for easier inventory control.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.