OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT 400G OSFP 8 x 50G PAM4 IHS/Finned Top Ethernet Active Optical Cable, 7m (23ft)

For short, high-density connections, this AOC cable combines 400G performance with a fixed 7m (23ft) cable run. It corresponds to Generic OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT and uses a factory-terminated active optical link with the optical engines and fiber integrated into the assembly.

OEM Part Number: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FTHT Part Number: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT

Product Highlights

• HT-manufactured AOC assembly in 7m (23ft)
• 400G connectivity at 400Gbps
• Interface configuration: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)
• Fixed length and part number: 7m (23ft), OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT
• Cable construction: Active Optical Cable
• Maximum power consumption: 10W Per End
• Minimum bend radius: 30mm
• Operating temperature: 0 to 70°C (32 to 158°F)

The listed modulation format is 8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The intended application is 400G Ethernet. Listed interface and protocol references include CMIS V4.0, OSFP MSA. Confirm that the host firmware and port configuration support the same operating mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

The extended 7m (23ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.

OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT occupies the middle of this family between OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-5M16FT at 5m (16ft) and OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-10M33FT at 10m (33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 10W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Our compatibility setup for Generic OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT is checked together with the physical 7m (23ft) assembly. Factory verification covers connector condition, host identification, error-free link establishment and optical link operation, receive activity and diagnostic readouts. Providing the exact host model and firmware release helps us identify platform-specific requirements before production.

Use part number OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-400G-AOC-7M23FT for the 7m (23ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.