OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT 800G Twin-port OSFP 8 x 100G PAM4 IHS/Finned Top Active Copper Twinax Cable, 4m (13ft)

Designed for hosts that recognize OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT, this OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top) cable delivers 800G transmission over a fixed 4m (13ft) assembly. Its ACC construction provides an actively conditioned copper link for the stated high-speed interface.

OEM Part Number: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FTHT Part Number: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT

Product Highlights

• HT-manufactured ACC assembly in 4m (13ft)
• 800G connectivity at 850Gbps (8x 106.25Gbps)
• Interface configuration: OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)
• Fixed length and part number: 4m (13ft), OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT
• Cable construction: Active DAC (ACC)
• Conductor specification: 26AWG
• Maximum power consumption: 1.3W Per End
• Minimum bend radius: 59.5mm

The listed modulation format is 8x100G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT occupies the middle of this family between OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-3M10FT at 3m (10ft) and OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-5M16FT at 5m (16ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 1.3W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 26AWG conductors, PET jacket, minimum bend radius 59.5mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is 800G Ethernet. Listed interface and protocol references include CMIS 5.0, IEEE 802.3ck, OSFP Rev5.0. Confirm that the host firmware and port configuration support the same operating mode.

The 4m (13ft) length gives OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT more freedom for adjacent-rack and row-end deployments. Longer copper runs need particular attention to routing weight and bend control; the ACC specification and host support must still match the intended link.

For this Generic application, testing combines digital identification with actual traffic-link verification and electrical continuity, link stability and diagnostic readouts. Both ends are inspected for latch, boot and connector damage. If the project uses a specific hardware revision or a channelized port, send those details so that the intended configuration can be reviewed before shipment.

Quote HT part number OSFP (IHS/Finned Top) to OSFP (IHS/Finned Top)-800G-ACC-4M13FT with the required quantity. The 4m (13ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Standard configurations normally ship within one to three working days. Worldwide courier, air freight and sea freight options are available, and shipments can also be sent on your own courier account or delivered to an appointed forwarder.