OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT 400G OSFP 8 x 50G PAM4 RHS/Flat Top to 400G QSFP-DD 8 x 50G PAM4 Active Optical Cable, 5m (16ft)

For short, high-density connections, this AOC cable combines 400G performance with a fixed 5m (16ft) cable run. It corresponds to Generic OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT and uses a factory-terminated active optical link with the optical engines and fiber integrated into the assembly.

OEM Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FTHT Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT

Product Highlights

• HT-manufactured AOC assembly in 5m (16ft)
• 400G connectivity at 400Gbps
• Interface configuration: OSFP (RHS/Flat Top) to QSFP-DD
• Fixed length and part number: 5m (16ft), OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT
• Cable construction: AOC
• Maximum power consumption: 10W (OSFP End) 10W (QSFP-DD End)
• Minimum bend radius: 30mm

The listed modulation format is OSFP-8x 50G-PAM4QSFP-DD-8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The rated power consumption is 10W (OSFP End) 10W (QSFP-DD End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include CMIS 4.0, IEEE 802.3bs-400GAUI-8, OSFP MSA, QSFP-DD MSA. Confirm that the host firmware and port configuration support the same operating mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

The 5m (16ft) length gives OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT more freedom for adjacent-rack and row-end deployments. The integrated optical assembly should be supported along its route without tight bends or connector pull loads; the AOC specification and host support must still match the intended link.

The HT cable carries the compatibility configuration associated with OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT, while its mechanical assembly remains the fixed 5m (16ft) version described here. Incoming inspection, connector examination and a live link test are completed before packing. Customers with unusually old or new Generic software can request a pre-order check.

Use part number OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-5M16FT for the 5m (16ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Quality control includes connector appearance, cable identification and functional verification. Packing materials are selected to keep the connector housings and cable boots from taking impact during transport, and the coil is not compressed into an undersized bundle. Volume orders can include customer-specific labels and packing documentation.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.