Juniper Networks QDD-2X100G-3M Compatible 200G QSFP-DD 8 x 25G NRZ to 2 x 100G QSFP28 4 x 25G NRZ Passive Copper Breakout Cable, 3m (10ft)

With a fixed 3m (10ft) cable and QSFP-DD to 2x QSFP28, the QDD-2X100G-3M compatible assembly simplifies 200G deployment. It is manufactured and tested by HT for Juniper Networks equipment.

OEM Part Number: QDD-2X100G-3MHT Part Number: QDD-2X100G-3M

Product Highlights

• Compatible alternative to Juniper Networks QDD-2X100G-3M
• 200G connectivity at 200Gbps
• Interface configuration: QSFP-DD to 2x QSFP28
• Fixed length and part number: 3m (10ft), QDD-2X100G-3M
• Cable construction: Passive Breakout DAC
• Conductor specification: 28AWG
• Maximum power consumption: 0.1W (QSFP-DD End)0.1W (QSFP28 Per End)
• Minimum bend radius: 35mm

Juniper platform documentation distinguishes straight QSFP28 DAC or AOC connections from DACBO and AOCBO breakout operation. On channelized systems, the host port must be configured for the required breakout mode. Match this HT compatible cable to the exact Juniper part number and the intended platform configuration.

The QSFP-DD to 2x QSFP28 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

At 3m (10ft), this assembly can bridge non-aligned ports or adjacent racks while remaining a single direct-attach link. Support longer horizontal runs with suitable cable management and preserve space for cooling and future maintenance.

QDD-2X100G-3M is the longest of 4 verified length options in this family. Compared with QDD-2X100G-2M at 2m (7ft), it provides 1m of additional reach for a longer vertical drop, a wider rack or an adjacent-cabinet route. Confirm that the complete path requires this length, because unused slack still needs supported, bend-safe storage.

The listed modulation format is QSFP-DD-8x 25G-NRZQSFP28-4x 25G-NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The rated power consumption is 0.1W (QSFP-DD End)0.1W (QSFP28 Per End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 28AWG conductors, PVC jacket, minimum bend radius 35mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD MSA, SFF-8661, IEEE 802.3bs-200GAUI-8, IEEE802.3bm-CAUI-4, CMIS 4.0, SFF-8636. Confirm that the host firmware and port configuration support the same operating mode.

The HT cable carries the compatibility configuration associated with QDD-2X100G-3M, while its mechanical assembly remains the fixed 3m (10ft) version described here. Incoming inspection, connector examination and a live link test are completed before packing. Customers with unusually old or new Juniper Networks software can request a pre-order check.

When ordering, specify QDD-2X100G-3M, cable length 3m (10ft) and the host platform. This allows our team to verify both the physical assembly and the compatibility requirement before production. Neutral labeling and customer packing lists can be arranged for volume orders.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Available stock is usually packed and handed to the carrier within one to three working days. Delivery can be arranged by international express, air cargo or sea freight, with tracking details supplied after dispatch. Freight-collect shipments and delivery to a customer warehouse or forwarder can also be coordinated.