QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT 200G QSFP-DD 8 x 25G NRZ to 8 x 25G SFP28 25G NRZ Active Optical Breakout Cable, 15m (49ft)

This HT cable matches the QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT requirement for multi-vendor equipment. The 15m (49ft) assembly supports 200G operation and provides a factory-terminated active optical link with the optical engines and fiber integrated into the assembly; its complete electrical and mechanical details are listed below.

OEM Part Number: QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FTHT Part Number: QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT

Product Highlights

• HT-manufactured AOC assembly in 15m (49ft)
• 200G connectivity at 206.24Gbps (8x 25.78Gbps)
• Interface configuration: QSFP-DD to 8x 25G SFP28
• Fixed length and part number: 15m (49ft), QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT
• Cable construction: OM3
• Maximum power consumption: QSFP-DD <4W,SFP28 <1W
• Minimum bend radius: 30mm
• Operating temperature: 0 to 70°C (32 to 158°F)

The listed modulation format is NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The extended 15m (49ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.

QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT occupies the middle of this family between QSFP-DD to 8x 25G SFP28-200G-AOC-10M33FT at 10m (33ft) and QSFP-DD to 8x 25G SFP28-200G-AOC-20M66FT at 20m (66ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is QSFP-DD <4W,SFP28 <1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD MSA V5.0,SFP28 MSA,CMIS V4.0,SFF-8472. Confirm that the host firmware and port configuration support the same operating mode.

The QSFP-DD to 8x 25G SFP28 configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

For this Generic application, testing combines digital identification with actual traffic-link verification and optical link operation, receive activity and diagnostic readouts. Both ends are inspected for latch, boot and connector damage. If the project uses a specific hardware revision or a channelized port, send those details so that the intended configuration can be reviewed before shipment.

When ordering, specify QSFP-DD to 8x 25G SFP28-200G-AOC-15M49FT, cable length 15m (49ft) and the host platform. This allows our team to verify both the physical assembly and the compatibility requirement before production. Neutral labeling and customer packing lists can be arranged for volume orders.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.