QSFP-DD to QSFP-DD-200G-DAC-2M7FT 200G QSFP-DD 8 x 25G NRZ Passive Copper Twinax Cable, 2m (7ft)

With a fixed 2m (7ft) cable and QSFP-DD to QSFP-DD, the QSFP-DD to QSFP-DD-200G-DAC-2M7FT compatible assembly simplifies 200G deployment. It is manufactured and tested by HT for multi-vendor equipment.

OEM Part Number: QSFP-DD to QSFP-DD-200G-DAC-2M7FTHT Part Number: QSFP-DD to QSFP-DD-200G-DAC-2M7FT

Product Highlights

• HT-manufactured DAC assembly in 2m (7ft)
• 200G connectivity at 200Gbps
• Interface configuration: QSFP-DD to QSFP-DD
• Fixed length and part number: 2m (7ft), QSFP-DD to QSFP-DD-200G-DAC-2M7FT
• Cable construction: Passive Twinax
• Conductor specification: 28AWG
• Maximum power consumption: 0.1W Per End
• Minimum bend radius: 40.5mm

The rated power consumption is 0.1W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

QSFP-DD to QSFP-DD-200G-DAC-2M7FT occupies the middle of this family between QSFP-DD to QSFP-DD-200G-DAC-1.5M5FT at 1.5m (5ft) and QSFP-DD to QSFP-DD-200G-DAC-2.5M8FT at 2.5m (8ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

This assembly uses 28AWG conductors, PVC jacket, minimum bend radius 40.5mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include IEEE 802.3bj, QSFP-DD MSA, CMIS, SFF-8417. Confirm that the host firmware and port configuration support the same operating mode.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

QSFP-DD to QSFP-DD-200G-DAC-2M7FT provides 2m (7ft) for connections between separated rack units or nearby equipment positions. Plan the route around cable managers and power cords, keeping the assembly free from connector strain while avoiding a large obstruction in the airflow path.

Our compatibility setup for Generic QSFP-DD to QSFP-DD-200G-DAC-2M7FT is checked together with the physical 2m (7ft) assembly. Factory verification covers connector condition, host identification, error-free link establishment and electrical continuity, link stability and diagnostic readouts. Providing the exact host model and firmware release helps us identify platform-specific requirements before production.

This product is ordered as QSFP-DD to QSFP-DD-200G-DAC-2M7FT in 2m (7ft). Include the equipment model and software release if you would like a pre-order compatibility review. Other lengths use different part numbers and should not be substituted into the same order line.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Standard configurations normally ship within one to three working days. Worldwide courier, air freight and sea freight options are available, and shipments can also be sent on your own courier account or delivered to an appointed forwarder.