QSFP-DD to QSFP-DD-400G-DAC-1M3FT 400G QSFP-DD 8 x 50G PAM4 Passive Copper Twinax Cable, 1m (3ft)

For short, high-density connections, this DAC cable combines 400G performance with a fixed 1m (3ft) cable run. It corresponds to Generic QSFP-DD to QSFP-DD-400G-DAC-1M3FT and uses a factory-terminated passive copper link without separate optical modules or patch cords.

OEM Part Number: QSFP-DD to QSFP-DD-400G-DAC-1M3FTHT Part Number: QSFP-DD to QSFP-DD-400G-DAC-1M3FT

Product Highlights

• HT-manufactured DAC assembly in 1m (3ft)
• 400G connectivity at 400Gbps
• Interface configuration: QSFP-DD to QSFP-DD
• Fixed length and part number: 1m (3ft), QSFP-DD to QSFP-DD-400G-DAC-1M3FT
• Cable construction: Passive Twinax
• Conductor specification: 30AWG
• Maximum power consumption: 0.1W Per End
• Minimum bend radius: 33mm

The listed modulation format is 8x 50Gbps PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The intended application is 400G Ethernet. Listed interface and protocol references include IEEE 802.3cd, QSFP-DD MSA, CMIS 4.0. Confirm that the host firmware and port configuration support the same operating mode.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

At 1m (3ft), QSFP-DD to QSFP-DD-400G-DAC-1M3FT is a practical choice for direct connections within one rack. Route the cable along the intended management path rather than pulling it diagonally across adjacent connectors, and leave enough clearance for insertion, removal and front-panel airflow.

QSFP-DD to QSFP-DD-400G-DAC-1M3FT occupies the middle of this family between QSFP-DD to QSFP-DD-400G-DAC-0.5M2FT at 0.5m (2ft) and QSFP-DD to QSFP-DD-400G-DAC-1.5M5FT at 1.5m (5ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 0.1W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 30AWG conductors, PET jacket, minimum bend radius 33mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The assembly is configured for equipment that recognizes QSFP-DD to QSFP-DD-400G-DAC-1M3FT. Before shipment, we inspect both connectors and verify identification, link establishment and electrical continuity, link stability and diagnostic readouts. Host hardware and firmware revisions can affect third-party cable acceptance, so customers can provide the equipment model and software release for a pre-order compatibility review.

Quote HT part number QSFP-DD to QSFP-DD-400G-DAC-1M3FT with the required quantity. The 1m (3ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

HT inspects and tests every completed cable before it enters finished stock. Protective caps or covers are fitted where applicable, followed by anti-static or tray packaging and an outer carton. Custom labels can cross-reference the customer part number, QSFP-DD to QSFP-DD-400G-DAC-1M3FT and the 1m (3ft) length for easier inventory control.

Stock items are generally dispatched within one to three working days after order confirmation. DHL, UPS, FedEx, TNT and EMS are available for international delivery; larger consolidated orders can move by air or sea freight. Customer courier accounts and nominated forwarders are accepted.