
With a fixed 7m (23ft) cable and QSFP-DD to QSFP-DD, the QSFP-DD to QSFP-DD-800G-AOC-7M23FT compatible assembly simplifies 800G deployment. It is manufactured and tested by HT for multi-vendor equipment.
OEM Part Number: QSFP-DD to QSFP-DD-800G-AOC-7M23FTHT Part Number: QSFP-DD to QSFP-DD-800G-AOC-7M23FT
| HT Part Number | QSFP-DD to QSFP-DD-800G-AOC-7M23FT |
|---|---|
| Manufacturer | HT |
| Form Factor | QSFP-DD to QSFP-DD |
| Max. Data Rate | 800Gbps |
| Cable Length | 7m (23ft) |
| Cable Type | AOC |
| Wavelength | 850nm |
| Minimum Bend Radius | 30mm |
| Transmitter Type | VCSEL |
| Receiver Type | PIN |
| Max. Power Consumption | ≤12W Per End |
| Modulation Format | 8x 100G-PAM4 |
| CDR (Clock and Data Recovery) | TX&RX Built-in CDR |
| Jacket Material | OFNP |
| DDM/DOM | Supported |
| Commercial Temperature Range | 0 to 70°C (32 to 158°F) |
| Protocols | QSFP-DD HW Specification Rev 6.3, CMIS Rev 5.0 |
The listed modulation format is 8x 100G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.
This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.
The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP-DD HW Specification Rev 6.3, CMIS Rev 5.0. Confirm that the host firmware and port configuration support the same operating mode.
The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.
The extended 7m (23ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.
QSFP-DD to QSFP-DD-800G-AOC-7M23FT occupies the middle of this family between QSFP-DD to QSFP-DD-800G-AOC-5M16FT at 5m (16ft) and QSFP-DD to QSFP-DD-800G-AOC-10M33FT at 10m (33ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 3m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.
The rated power consumption is ≤12W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.
Each QSFP-DD to QSFP-DD-800G-AOC-7M23FT compatible cable is powered up on a suitable test interface rather than checked only for continuity. We confirm the expected identification and observe optical link operation, receive activity and diagnostic readouts. Because operating systems can apply different qualification rules by hardware revision, the intended Generic platform should be included with the order.
This product is ordered as QSFP-DD to QSFP-DD-800G-AOC-7M23FT in 7m (23ft). Include the equipment model and software release if you would like a pre-order compatibility review. Other lengths use different part numbers and should not be substituted into the same order line.
No. It is manufactured by HT under our own manufacturer identity.
No. This page is dedicated to 7m (23ft) and part number QSFP-DD to QSFP-DD-800G-AOC-7M23FT. Other lengths have their own part numbers and product pages.
No. The connectors and cable form one complete direct-attach assembly. Do not attempt to detach or replace either end.
No. Follow the specified minimum bend radius and route the 7m (23ft) assembly without tight folds, sharp edges or excessive cable ties.
HT inspects and tests every completed cable before it enters finished stock. Protective caps or covers are fitted where applicable, followed by anti-static or tray packaging and an outer carton. Custom labels can cross-reference the customer part number, QSFP-DD to QSFP-DD-800G-AOC-7M23FT and the 7m (23ft) length for easier inventory control.
Available stock is usually packed and handed to the carrier within one to three working days. Delivery can be arranged by international express, air cargo or sea freight, with tracking details supplied after dispatch. Freight-collect shipments and delivery to a customer warehouse or forwarder can also be coordinated.
Please write to sales@huihongfiber.com, we will reply as soon as possible.
| Fiber Optic Test Equipment |
| Fiber Optic Tool Kits |
Huihong TechnologiesAdd:6F,1st Bldg,ZYT industrial park, Shiyan area,Shenzhen,ChinaEmail:info@huihongfiber.com Tel: 86.755.61230063 Specialized fiber optic products manufacturer. |
Fiber Optic Quick Guide |
News and ExhibitionsCompany news and exhibitions schedules for this year and next year. click here for details . |
Fiber Optic Applications
|
Customer Support
|