QSFP112 to QSFP112-400G-AEC-2M7FT 400G QSFP112 4 x 100G PAM4 Active Electrical Cable, 2m (7ft)

This HT cable matches the QSFP112 to QSFP112-400G-AEC-2M7FT requirement for multi-vendor equipment. The 2m (7ft) assembly supports 400G operation and provides an active electrical link with signal recovery designed for the stated data rate; its complete electrical and mechanical details are listed below.

OEM Part Number: QSFP112 to QSFP112-400G-AEC-2M7FTHT Part Number: QSFP112 to QSFP112-400G-AEC-2M7FT

Product Highlights

• HT-manufactured AEC assembly in 2m (7ft)
• 400G connectivity at 400Gbps
• Interface configuration: QSFP112 to QSFP112
• Fixed length and part number: 2m (7ft), QSFP112 to QSFP112-400G-AEC-2M7FT
• Cable construction: Active DAC (AEC)
• Conductor specification: 32AWG
• Maximum power consumption: <8W Per End
• Minimum bend radius: 26.5mm

The listed modulation format is 4x 100G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

This assembly uses 32AWG conductors, PET jacket, minimum bend radius 26.5mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include QSFP112 MSA, IEEE 802.3ck 400GBase-CR4, CMIS 5.0. Confirm that the host firmware and port configuration support the same operating mode.

QSFP112 to QSFP112-400G-AEC-2M7FT provides 2m (7ft) for connections between separated rack units or nearby equipment positions. Plan the route around cable managers and power cords, keeping the assembly free from connector strain while avoiding a large obstruction in the airflow path.

QSFP112 to QSFP112-400G-AEC-2M7FT occupies the middle of this family between QSFP112 to QSFP112-400G-AEC-1M3FT at 1m (3ft) and QSFP112 to QSFP112-400G-AEC-3M10FT at 3m (10ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is <8W Per End. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

The assembly is configured for equipment that recognizes QSFP112 to QSFP112-400G-AEC-2M7FT. Before shipment, we inspect both connectors and verify identification, link establishment and electrical continuity, link stability and diagnostic readouts. Host hardware and firmware revisions can affect third-party cable acceptance, so customers can provide the equipment model and software release for a pre-order compatibility review.

Use part number QSFP112 to QSFP112-400G-AEC-2M7FT for the 2m (7ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.