QSFP28-DD to Duplex-LC-200G-AOC-15M49FT 200G QSFP-DD 8 x 25G NRZ to 8 x 25G LC Duplex Active Optical Breakout Cable, 15m (49ft)

The HT-manufactured QSFP28-DD to Duplex-LC-200G-AOC-15M49FT compatible cable provides 200G connectivity for multi-vendor equipment. This 15m (49ft) version is a factory-terminated active optical link with the optical engines and fiber integrated into the assembly, with an exact part number and length that can be matched directly to the equipment requirement.

OEM Part Number: QSFP28-DD to Duplex-LC-200G-AOC-15M49FTHT Part Number: QSFP28-DD to Duplex-LC-200G-AOC-15M49FT

Product Highlights

• HT-manufactured AOC assembly in 15m (49ft)
• 200G connectivity at 200Gbps
• Interface configuration: QSFP28-DD to Duplex-LC
• Fixed length and part number: 15m (49ft), QSFP28-DD to Duplex-LC-200G-AOC-15M49FT
• Cable construction: Optical Cable
• Maximum power consumption: ≤3.47W
• Minimum bend radius: 30mm

The listed modulation format is NRZ. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The extended 15m (49ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.

QSFP28-DD to Duplex-LC-200G-AOC-15M49FT occupies the middle of this family between QSFP28-DD to Duplex-LC-200G-AOC-10M33FT at 10m (33ft) and QSFP28-DD to Duplex-LC-200G-AOC-20M66FT at 20m (66ft). It adds 5m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is ≤3.47W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is Ethernet, 5G Front Haul. Listed interface and protocol references include QSFP-DD MSA CMIS 4.0, IEEE 802.3bs 200G-SR8, IEEE 802.3by 25G-SR. Confirm that the host firmware and port configuration support the same operating mode.

The QSFP28-DD to Duplex-LC configuration divides the high-speed interface into multiple lower-speed connections. Verify the upstream lane assignment, downstream port speeds and breakout setting on the host before connecting the assembly. Each branch must attach to the correct remote interface.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Each QSFP28-DD to Duplex-LC-200G-AOC-15M49FT compatible cable is powered up on a suitable test interface rather than checked only for continuity. We confirm the expected identification and observe optical link operation, receive activity and diagnostic readouts. Because operating systems can apply different qualification rules by hardware revision, the intended Generic platform should be included with the order.

Use part number QSFP28-DD to Duplex-LC-200G-AOC-15M49FT for the 15m (49ft) assembly. For mixed-length projects, list each required part number and quantity separately so that every cable can be tested and packed according to its intended installation.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Lead time for ordinary configurations is normally one to three working days, while production quantities are confirmed with the order. We can arrange express courier or economy freight according to destination and carton volume, or hand the shipment to your appointed logistics provider.