SFP-DD to SFP-DD-100G-AOC-10M33FT 100G SFP-DD 2 x 50G PAM4 Active Optical Cable, 10m (33ft)

The SFP-DD to SFP-DD-100G-AOC-10M33FT cable offers a direct SFP-DD to SFP-DD connection at 100Gbps. Its 10m (33ft) length and AOC construction are intended for multi-vendor equipment, with no separate transceiver-and-patch-cord assembly required.

OEM Part Number: SFP-DD to SFP-DD-100G-AOC-10M33FTHT Part Number: SFP-DD to SFP-DD-100G-AOC-10M33FT

Product Highlights

• HT-manufactured AOC assembly in 10m (33ft)
• 100G connectivity at 100Gbps
• Interface configuration: SFP-DD to SFP-DD
• Fixed length and part number: 10m (33ft), SFP-DD to SFP-DD-100G-AOC-10M33FT
• Cable construction: OM4
• Maximum power consumption: ≤3.5W
• Minimum bend radius: 60mm

The listed modulation format is 2x 50G-PAM4 to 2x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

The extended 10m (33ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.

SFP-DD to SFP-DD-100G-AOC-10M33FT occupies the middle of this family between SFP-DD to SFP-DD-100G-AOC-7M23FT at 7m (23ft) and SFP-DD to SFP-DD-100G-AOC-15M49FT at 15m (49ft). It adds 3m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is ≤3.5W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses minimum bend radius 60mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFP-DD MSA, SFP-DD MIS. Confirm that the host firmware and port configuration support the same operating mode.

Each SFP-DD to SFP-DD-100G-AOC-10M33FT compatible cable is powered up on a suitable test interface rather than checked only for continuity. We confirm the expected identification and observe optical link operation, receive activity and diagnostic readouts. Because operating systems can apply different qualification rules by hardware revision, the intended Generic platform should be included with the order.

Quote HT part number SFP-DD to SFP-DD-100G-AOC-10M33FT with the required quantity. The 10m (33ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Standard configurations normally ship within one to three working days. Worldwide courier, air freight and sea freight options are available, and shipments can also be sent on your own courier account or delivered to an appointed forwarder.