SFP112 to SFP112-100G-DAC-1.5M5FT 100G SFP112 PAM4 Passive Copper Twinax Cable, 1.5m (5ft)

For short, high-density connections, this DAC cable combines 100G performance with a fixed 1.5m (5ft) cable run. It corresponds to Generic SFP112 to SFP112-100G-DAC-1.5M5FT and uses a factory-terminated passive copper link without separate optical modules or patch cords.

OEM Part Number: SFP112 to SFP112-100G-DAC-1.5M5FTHT Part Number: SFP112 to SFP112-100G-DAC-1.5M5FT

Product Highlights

• HT-manufactured DAC assembly in 1.5m (5ft)
• 100G connectivity at 100Gbps
• Interface configuration: SFP112 to SFP112
• Fixed length and part number: 1.5m (5ft), SFP112 to SFP112-100G-DAC-1.5M5FT
• Cable construction: Passive Twinax
• Conductor specification: 28AWG
• Maximum power consumption: <0.15W
• Minimum bend radius: 20mm

The listed modulation format is 100G-PAM4 to 100G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The intended application is 100G Ethernet.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

The additional half metre beyond a one-metre assembly gives SFP112 to SFP112-100G-DAC-1.5M5FT useful routing flexibility when the ports are not directly aligned. It can accommodate a different rack unit or a short service loop, but excess cable should be dressed loosely rather than folded into a tight coil.

SFP112 to SFP112-100G-DAC-1.5M5FT occupies the middle of this family between SFP112 to SFP112-100G-DAC-1M3FT at 1m (3ft) and SFP112 to SFP112-100G-DAC-2M7FT at 2m (7ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is <0.15W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses 28AWG conductors, PVC (OFNR) jacket, minimum bend radius 20mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The assembly is configured for equipment that recognizes SFP112 to SFP112-100G-DAC-1.5M5FT. Before shipment, we inspect both connectors and verify identification, link establishment and electrical continuity, link stability and diagnostic readouts. Host hardware and firmware revisions can affect third-party cable acceptance, so customers can provide the equipment model and software release for a pre-order compatibility review.

Quote HT part number SFP112 to SFP112-100G-DAC-1.5M5FT with the required quantity. The 1.5m (5ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Available stock is usually packed and handed to the carrier within one to three working days. Delivery can be arranged by international express, air cargo or sea freight, with tracking details supplied after dispatch. Freight-collect shipments and delivery to a customer warehouse or forwarder can also be coordinated.