Dell (Force10) CBL-10GSFP-DAC-2.5M Compatible 10G SFP+ Passive Copper Twinax Cable, 2.5m (8ft)

With a fixed 2.5m (8ft) cable and SFP+ to SFP+, the (Force10) CBL-10GSFP-DAC-2.5M compatible assembly simplifies 10G deployment. It is manufactured and tested by HT for Dell equipment.

OEM Part Number: (Force10) CBL-10GSFP-DAC-2.5MHT Part Number: (Force10) CBL-10GSFP-DAC-2.5M

Product Highlights

• Compatible alternative to Dell (Force10) CBL-10GSFP-DAC-2.5M
• 10G connectivity at 10Gbps
• Interface configuration: SFP+ to SFP+
• Fixed length and part number: 2.5m (8ft), (Force10) CBL-10GSFP-DAC-2.5M
• Cable construction: Passive Twinax
• Conductor specification: 30AWG
• Maximum power consumption: ≤0.1W
• Minimum bend radius: 23mm

The rated power consumption is ≤0.1W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

The intended application is 10G Ethernet. Listed interface and protocol references include 1x InfiniBand QDR, DDR, SDR, 10 Gigabit Ethernet, Fibre Channel. Confirm that the host firmware and port configuration support the same operating mode.

A passive DAC has no separate optical conversion stage. Its low-power, low-latency operation is useful for short equipment links, but the assembly must remain within the length and signaling mode accepted by both hosts.

The 2.5m (8ft) version is useful when a two-metre run would leave insufficient working slack. Before installation, check the complete horizontal and vertical path so that (Force10) CBL-10GSFP-DAC-2.5M reaches both ports without tension at either connector.

(Force10) CBL-10GSFP-DAC-2.5M occupies the middle of this family between (Force10) CBL-10GSFP-DAC-2M at 2m (7ft) and (Force10) CBL-10GSFP-DAC-3M at 3m (10ft). It adds 0.5m over the shorter option for extra routing clearance, while the next longer version adds another 0.5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

This assembly uses 30AWG conductors, PVC (OFNR) jacket, minimum bend radius 23mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

Compatibility is more than matching the SFP+ to SFP+ shape. This assembly is prepared for hosts expecting (Force10) CBL-10GSFP-DAC-2.5M and is checked for identification, stable link behavior and electrical continuity, link stability and diagnostic readouts. We recommend confirming the equipment model and software release for critical deployments or mixed-vendor installations.

Quote HT part number (Force10) CBL-10GSFP-DAC-2.5M with the required quantity. The 2.5m (8ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

Production inspection covers both physical condition and a live link check. Connector ends receive individual protection, and the completed assembly is packed without tight ties or sharp bends. For multi-length projects, cartons can be separated and labelled by OEM part number to simplify installation on site.

Standard configurations normally ship within one to three working days. Worldwide courier, air freight and sea freight options are available, and shipments can also be sent on your own courier account or delivered to an appointed forwarder.