OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT 400G OSFP 4 x 100G PAM4 RHS/Flat Top to 400G QSFP-DD 8 x 50G PAM4 Active Optical Cable, 10m (33ft)

This HT cable matches the OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT requirement for multi-vendor equipment. The 10m (33ft) assembly supports 400G operation and provides a factory-terminated active optical link with the optical engines and fiber integrated into the assembly; its complete electrical and mechanical details are listed below.

OEM Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FTHT Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT

Product Highlights

• HT-manufactured AOC assembly in 10m (33ft)
• 400G connectivity at 400Gbps
• Interface configuration: OSFP (RHS/Flat Top) to QSFP-DD
• Fixed length and part number: 10m (33ft), OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT
• Cable construction: AOC
• Maximum power consumption: 14W (OSFP End)10W (QSFP-DD End)
• Minimum bend radius: 30mm
• Operating temperature: 0 to 70°C (32 to 158°F)

The listed modulation format is OSFP-4x 100G-PAM4QSFP-DD-8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

The extended 10m (33ft) reach supports connections across adjacent racks or between separated equipment rows. Secure the cable along its route, protect both ends from pull loads and preserve ventilation. The integrated AOC construction avoids a chain of separate modules and patch leads.

OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT occupies the middle of this family between OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-7M23FT at 7m (23ft) and OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-15M49FT at 15m (49ft). It adds 3m over the shorter option for extra routing clearance, while the next longer version adds another 5m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 14W (OSFP End)10W (QSFP-DD End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include OSFP MSA, QSFP-DD MSA, CMIS 4.0, IEEE 802.3ck-400GAUI-4, IEEE 802.3bs-400GAUI-8. Confirm that the host firmware and port configuration support the same operating mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Each OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT compatible cable is powered up on a suitable test interface rather than checked only for continuity. We confirm the expected identification and observe optical link operation, receive activity and diagnostic readouts. Because operating systems can apply different qualification rules by hardware revision, the intended Generic platform should be included with the order.

Quote HT part number OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT with the required quantity. The 10m (33ft) length is fixed for this part number; if a different length is needed, select its corresponding page and OEM reference from the length list above. Standard HT labels and project-specific packaging are available.

Every OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-10M33FT compatible assembly undergoes link testing, compatibility verification and visual inspection. The 10m (33ft) cable is coiled without exceeding its minimum bend radius, fitted with connector protection and packed in an anti-static bag or protective tray before cartoning. Project labels and packing lists are available for volume orders.

Standard configurations normally ship within one to three working days. Worldwide courier, air freight and sea freight options are available, and shipments can also be sent on your own courier account or delivered to an appointed forwarder.