OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT 400G OSFP 4 x 100G PAM4 RHS/Flat Top to 400G QSFP-DD 8 x 50G PAM4 Active Optical Cable, 2m (7ft)

Designed for hosts that recognize OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT, this OSFP (RHS/Flat Top) to QSFP-DD cable delivers 400G transmission over a fixed 2m (7ft) assembly. Its AOC construction provides a factory-terminated active optical link with the optical engines and fiber integrated into the assembly.

OEM Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FTHT Part Number: OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT

Product Highlights

• HT-manufactured AOC assembly in 2m (7ft)
• 400G connectivity at 400Gbps
• Interface configuration: OSFP (RHS/Flat Top) to QSFP-DD
• Fixed length and part number: 2m (7ft), OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT
• Cable construction: AOC
• Maximum power consumption: 14W (OSFP End)10W (QSFP-DD End)
• Minimum bend radius: 30mm
• Operating temperature: 0 to 70°C (32 to 158°F)

The listed modulation format is OSFP-4x 100G-PAM4QSFP-DD-8x 50G-PAM4. Both host interfaces must be configured for the same aggregate rate and lane arrangement. A connector that fits mechanically does not by itself guarantee that the remote port supports this encoding or breakout mode.

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include OSFP MSA, QSFP-DD MSA, CMIS 4.0, IEEE 802.3ck-400GAUI-4, IEEE 802.3bs-400GAUI-8. Confirm that the host firmware and port configuration support the same operating mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT provides 2m (7ft) for connections between separated rack units or nearby equipment positions. Plan the route around cable managers and power cords, keeping the assembly free from connector strain while avoiding a large obstruction in the airflow path.

OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT occupies the middle of this family between OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-1M3FT at 1m (3ft) and OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-3M10FT at 3m (10ft). It adds 1m over the shorter option for extra routing clearance, while the next longer version adds another 1m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

The rated power consumption is 14W (OSFP End)10W (QSFP-DD End). Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

The HT cable carries the compatibility configuration associated with OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT, while its mechanical assembly remains the fixed 2m (7ft) version described here. Incoming inspection, connector examination and a live link test are completed before packing. Customers with unusually old or new Generic software can request a pre-order check.

This product is ordered as OSFP (RHS/Flat Top) to QSFP-DD-400G-AOC-2M7FT in 2m (7ft). Include the equipment model and software release if you would like a pre-order compatibility review. Other lengths use different part numbers and should not be substituted into the same order line.

Before packing, our team checks the cable jacket, connector boots, latches and identification of each assembly. The cable is then secured in a loose coil and protected against dust and connector impact. Neutral packaging, customer part-number labels and project-specific carton lists can be supplied on request.

Available stock is usually packed and handed to the carrier within one to three working days. Delivery can be arranged by international express, air cargo or sea freight, with tracking details supplied after dispatch. Freight-collect shipments and delivery to a customer warehouse or forwarder can also be coordinated.