SFP+ to SFP+-10G-AOC-5M16FT 10G SFP+ Active Optical Cable, 5m (16ft)

This 5m (16ft) AOC cable is built for multi-vendor equipment requiring the SFP+ to SFP+-10G-AOC-5M16FT interface. The 10Gbps link uses SFP+ to SFP+ and is supplied as one complete tested assembly.

OEM Part Number: SFP+ to SFP+-10G-AOC-5M16FTHT Part Number: SFP+ to SFP+-10G-AOC-5M16FT

Product Highlights

• HT-manufactured AOC assembly in 5m (16ft)
• 10G connectivity at 10Gbps
• Interface configuration: SFP+ to SFP+
• Fixed length and part number: 5m (16ft), SFP+ to SFP+-10G-AOC-5M16FT
• Cable construction: OM2/OM3
• Maximum power consumption: <0.8W
• Minimum bend radius: 30mm

The rated power consumption is <0.8W. Include this load in the host-port power and thermal budget, especially in densely populated switches. Maintain front-panel clearance and do not bundle the cable so tightly that it obstructs airflow around the connectors.

The 5m (16ft) length gives SFP+ to SFP+-10G-AOC-5M16FT more freedom for adjacent-rack and row-end deployments. The integrated optical assembly should be supported along its route without tight bends or connector pull loads; the AOC specification and host support must still match the intended link.

SFP+ to SFP+-10G-AOC-5M16FT occupies the middle of this family between SFP+ to SFP+-10G-AOC-3M10FT at 3m (10ft) and SFP+ to SFP+-10G-AOC-7M23FT at 7m (23ft). It adds 2m over the shorter option for extra routing clearance, while the next longer version adds another 2m. Measure the managed path and choose this version when its reach is sufficient without creating the slack associated with the longer assembly.

This assembly uses OFNP jacket, minimum bend radius 30mm. These mechanical characteristics affect how the cable should be dressed behind the equipment. Avoid sharp edges, excessive ties and repeated tight bends close to the connector boots.

The intended application is determined by the host interface and protocol support. Listed interface and protocol references include SFF-8636, 1xInfiniBand QDR,DDR,SDR, 10G Gigabit Ethernet. Confirm that the host firmware and port configuration support the same operating mode.

The optical engines and fiber are permanently integrated into this AOC. There are no detachable optical modules to clean or exchange. Handle the complete assembly by its connector housings and cable, and keep both ends matched to the same interface specification.

Each SFP+ to SFP+-10G-AOC-5M16FT compatible cable is powered up on a suitable test interface rather than checked only for continuity. We confirm the expected identification and observe optical link operation, receive activity and diagnostic readouts. Because operating systems can apply different qualification rules by hardware revision, the intended Generic platform should be included with the order.

This product is ordered as SFP+ to SFP+-10G-AOC-5M16FT in 5m (16ft). Include the equipment model and software release if you would like a pre-order compatibility review. Other lengths use different part numbers and should not be substituted into the same order line.

HT inspects and tests every completed cable before it enters finished stock. Protective caps or covers are fitted where applicable, followed by anti-static or tray packaging and an outer carton. Custom labels can cross-reference the customer part number, SFP+ to SFP+-10G-AOC-5M16FT and the 5m (16ft) length for easier inventory control.

Stock items are generally dispatched within one to three working days after order confirmation. DHL, UPS, FedEx, TNT and EMS are available for international delivery; larger consolidated orders can move by air or sea freight. Customer courier accounts and nominated forwarders are accepted.